
A PES supercharger is a bolt on kit from the American specialist Performance Engineered Systems that adds an Eaton Roots type supercharger to Audi petrol engines. PES built three main families for Audi: the G2 for the 2.8 V6, the G3 for the 3.0 V6 and the G4 for the 4.2 V8, including the RS4 B7 and the R8. The G4 for the 4.2 FSI V8 is the best known, with a claimed 558 hp for the R8.
PES supercharger kits at a glance
| Kit | Engine | Main Audi models | Supercharger | Boost |
|---|---|---|---|---|
| G2 | 2.8 V6 30 valve | A4 B5 (1998 to 2001), A6 C5 2.8 | Eaton M62 | Low boost, not published |
| G3 | 3.0 V6 30 valve | A4 B6 3.0 (2002 to 2005) | Eaton | Not published |
| G4 MPI | 4.2 V8 5 valve, port injection | S4 B6 and B7, S6 C5, A6 and A8 4.2, allroad 4.2, VW Touareg | Eaton M90 | 5 to 7 psi |
| G4 FSI | 4.2 V8 FSI, direct injection | RS4 B7, R8, S5 B8, plus A6, A8 and Q7 4.2 FSI | Eaton M90 | About 5 to 6 psi |
How a PES supercharger works
Every PES kit follows the same recipe. A cast aluminium intake manifold replaces the factory part and carries an Eaton supercharger, driven by the crankshaft through a new belt. The Eaton is a Roots type, positive displacement unit, so it pushes air into the engine from very low revs and the extra torque arrives instantly, with no turbo lag. Eaton superchargers are also used as original equipment by Mercedes Benz, Jaguar and Aston Martin.
More air needs more fuel, so the kits add larger injectors, and PES writes its own calibration for the engine control unit to keep the air and fuel ratio safe. The brackets are machined from billet aluminium and anodised, and PES said each kit was developed with more than 1,000 hours of road testing and data logging. Boost is deliberately modest, which is why PES described its priorities as reliability first, then torque, then power.
PES G2: the supercharger for the 2.8 V6
The G2 is the kit most searched for today. It was designed for the 30 valve 2.8 V6 in the A4 B5 and was also fitted to the A6 C5 2.8. The engine produced 193 PS as standard, and PES claimed about 295 hp at the crank with the supercharger, a gain of around half.
The installation manual shows how complete the kit was. It includes a new intake manifold with seals, the Eaton supercharger with its own synthetic lubricant, a pulley and a new serpentine belt, six new fuel injectors, a PES fuel pressure regulator, and a new power steering pump bracket and hose. The same manual covers early 1998 cars and the later drive by wire models, with notes on where the steps differ.
Owners who used the extra torque hard often fitted a stronger clutch at the same time, and the manual itself labels the kit for racing or off road use, a point to remember when it comes to registration and insurance.
PES G3: the 3.0 V6 in the A4 B6
The G3 followed for the 3.0 V6 introduced in the A4 B6 in 2002. It uses the same Eaton based concept and was planned for launch in the summer of 2002, covering the A4 3.0 built from 2002 to 2005. PES published fewer details for the G3 than for its other kits, and it is the rarest of the family today.
PES G4 for the 4.2 V8 with port injection
The first G4 was designed for the 5 valve 4.2 V8 with multi point injection, the engine of the S4 B6 and B7, the S6 C5, the A6 and A8 4.2 of 2000 to 2006, the allroad 4.2 and the VW Touareg. It moved up to the larger Eaton M90 and was sold in three stages:
| Stage | Boost | Intercooler | Gain claimed by PES |
|---|---|---|---|
| Stage 1 | 5 psi | No | About 20 to 25 per cent |
| Stage 1 Plus | 5 psi | Air to liquid | About 35 per cent |
| Stage 2 | 7 psi | Air to liquid | About 40 to 45 per cent, S4 with manual gearbox only |
PES measured these gains at the wheels on Dynojet and Mustang dynamometers. A Stage 1 car could later be upgraded to an intercooled kit without removing the manifold, and Stage 1 Plus was calibrated for the Tiptronic automatic. For the S6 C5, Dutch site AudiBlog reported in 2009 that the kit could take the 340 PS V8 to about 450 PS, the output of the first RS6.
PES G4 for the 4.2 FSI: RS4, R8 and S5
The most ambitious PES supercharger is the G4 for the direct injection 4.2 FSI V8 used in the RS4 B7, the R8 and the S5 B8. It also uses an Eaton M90, with a conservative boost of around 5 to 6 psi, and adds an air to liquid intercooler with its own cooling circuit and three heat exchangers behind the front bumper. The inlet manifold is prepared for optional water and methanol injection.
For the R8 and RS4, both rated at 420 hp as standard, PES claimed 558 hp at 7,900 rpm and 437 lb ft (about 592 Nm) at 4,840 rpm, a rise of 138 hp and 120 lb ft. Because the Eaton fills in the low and middle rev range, the gain in everyday driving feels even bigger than the peak figures suggest. In Europe, the G4 FSI kits were sold through Audi Superchargers UK, which presented upgraded versions in 2012.
Buying a used PES supercharger kit today
Most PES kits on offer today appear to be second hand, often already fitted to a car. Before buying one, check these points:
- Is the kit complete? Manifold, supercharger, pulley, belt, injectors, fuel regulator, brackets and, for intercooled kits, the pump, radiator and reservoir.
- Software. The PES calibration is matched to the kit and the engine. Make sure the car runs the right file and that a specialist can still read and adjust it.
- Supercharger health. Eaton units have their own oil. Ask when it was last changed and listen for bearing noise.
- Drivetrain. Check the clutch, the gearbox and the cooling system, which all work harder with the extra torque.
- Approval and insurance. Many kits were sold for off road use. Check with your registration authority and tell your insurer before driving the car on the road.
Our view
PES gave Audi owners something rare in the 2000s: a complete, well engineered way to add a Roots supercharger to engines that Audi only ever built naturally aspirated. The G2 turned the modest 2.8 V6 into a genuinely quick car, and the G4 FSI took the RS4 and R8 into supercar territory with the instant response a supercharger gives. Today these kits are period pieces, so condition and software support matter more than the original claims, but a well kept PES car is still one of the most interesting ways to drive an older Audi.
Frequently asked questions
What is a PES supercharger?
It is a bolt on supercharger kit from Performance Engineered Systems (PES), built around an Eaton Roots type supercharger, a cast aluminium intake manifold, larger injectors and a PES engine calibration.
Which Audi engines can use a PES supercharger?
PES made the G2 for the 2.8 V6, the G3 for the 3.0 V6 and the G4 for the 4.2 V8, in versions for the port injected engine (S4, S6, A6, A8, allroad) and for the 4.2 FSI (RS4 B7, R8, S5).
How much power does the PES G4 add to an Audi R8 or RS4?
PES claimed 558 hp and 437 lb ft for the R8 and RS4 with the G4 FSI kit, up from 420 hp, a gain of about a third.
How much power does the PES G2 give the 2.8 V6?
PES claimed about 295 hp at the crank for the 2.8 V6 with the G2 kit, compared with 193 PS as standard.
More supercharger tuning on Audi Tuning Mag
- Upgraded PES G4 supercharger kits for the R8, RS4 B7 and S5 V8
- TTS Rotrex supercharger for the Audi B8 S5 and B7 RS4
- APR supercharger pulley upgrade for the Audi 3.0 TFSI
- Forge Motorsport supercharger reduction pulley for the Audi S5 3.0 TFSI
Sources: PES G2 installation manual; PES G4 announcement (TeamSpeed); PES G4 kit for the Audi R8 (FR Tuning).

nice system. I want one
For any more information please contact me. Patrick@PES-Tuning.com
USA 267-597-3838 x13
Thank you, Patrick
I got the G2 three years ago from PES and have loved it. I put about 30,000 miles on my A6 since then without any other mods. No problems have come up. This is a great system. It shaved almost 3 seconds off the 0-60 time. It is also very tame while driving slowly, but pulls hard when needed.
10463-6349
Price???